Washer hoses are an integral part of how the appliance works.
If the hose is not in good shape, it’s going to fall off and/or create performance issues for the appliance.
This is when you are going to notice it will not have the right water pressure and/or it is not going to wash the way you want it to. This is not a good thing and you will want to figure out what is happening instantly.
With this in mind, it becomes important to learn how to fix a corroded washer hose connection.
To remove a corroded washer hose connection, you will want to inspect the washer hose to see where the damage is, use a Dremel tool to cut the connection in two spots, and then unscrew the fitting to get it out.
It is important to cut it into two pieces as that will make it easier to access the fitting and ensure it comes out as you want it to.
Otherwise, you will damage the connection point and this will make it a much bigger repair job as the new replacement won’t slide into place easily.
Here is more on what you have to do when looking to remove a corroded washer hose connection.
Table of Contents
Best Washing Machine Sheets (EDITOR’S CHOICE)
No products found.
Steps To Remove A Corroded Washer Hose Connection
1. Inspect The Washer Hose Connection
When you have a rusted washer hose connection, it’s important to know how bad the situation is.
What is this information going to do for you?
It will make it easier to pinpoint where you can cut using a good cutting tool. If you are unaware of where the rust has spread, you are going to cut in the wrong place and damage the connection point.
You will also want to use the time to inspect the surrounding components for damage.
When rust spreads, it will do a lot of damage nearby.
2. Use Dremel Tool To Cut In Two Spots
Now it is time to start focusing on how you are going to cut the washer hose connection that has corroded.
To do this, you are going to want to take out a Dremel tool.
This is the right tool to dig through the washer hose connection and make sure it does not damage anything else.
It is common for a person to want to cut it in one spot to pull it out. This is not the right way to go.
You want to cut it in two spots and then pull out the rusted portion of the connection. This will allow you to get that out of the way first.
3. Pull Off The Cut Parts
Now that the rusted washer hose connection is out of the way, you are going to have clearer access to the fitting.
This is a good sign you will be able to take out the rest of the fitting and then put in a new washer hose.
Make sure to slide out the cut parts and put them aside before doing this.
It is important to think about this so you don’t end up making a mistake and ruining the washer hose connection point.
4. Unscrew The Fitting To Access Connection Point
As you begin to unscrew the fitting, you will now want to go out and find a replacement washer hose.
It is important to find a compatible solution to make sure it is a perfect fit.
This is the only way to ensure it does not get damaged and you do have full access to the fitting.
As you begin to inspect the fitting, you will want to be thorough about how you approach it. This is a must.
Continue to work on the fitting and make sure it has been unscrewed properly before you slide the new washer hose into place.
When it is secure, you are going to want to test the washer to see if the water goes through as intended.
Final Thoughts
Look into these tips when you are trying to remove a corroded washer hose connection.
If you are looking to remove a corroded washer hose connection, it’s best to start by inspecting where the rust is, using a Dremel tool to cut it into two parts, and then accessing the fitting. Now, unscrew the fitting and set up the new washer hose.
This is how you are going to get the washer hose to work as it should.
The most important part of this process is to cut in the right spot. If you don’t do this, you are going to yank on the wrong part of the fitting and damage it.
Here’s More On Homes: