When a dishwasher is installed, it should look seamless but that’s not always the case.
This creates an uncertain situation where the dishwasher runs but it looks out of place. You will notice it will stand out for all the wrong reasons and that is when it’s time to make a change.
What type of change is best?
You will have to figure out why there is a gap between the dishwasher and floor before doing anything else.
If there is a gap between the dishwasher and floor, start by cutting a measured strip of plywood and silicone it in the gap. Next, find flat molding, press it on top of the plywood, and use silicone to glue it into place. This will take care of the ungainly gap.
When you are doing something like this such as filling the gap between a dishwasher and the floor, it’s important to think about how permanent the solution is.
You don’t want a situation where the solution works in the short-term, but that boxes in the dishwasher making it impossible to take out later.
You will have to be careful about this and only use a semi-permanent solution such as the one mentioned in this guide.
Best Pry Bar (EDITOR’S CHOICE)
No products found.
Steps To Follow If There’s A Gap Between Dishwasher And Floor
1. Place Plywood In The Gap
If there is a gap between the dishwasher and the floor, it’s important to measure it.
You will want to know the length, width, and depth before beginning to work on a long-term solution.
Do not attempt to fix it until you have the measurements in hand.
Next, you are going to want to find a smooth strip of plywood. This plywood is going to be used as the base for your fix.
You will want to cut it based on the measurements you have. It should be a perfect fit for the gap.
Now, install the plywood in and make sure it is ready to be glued into place.

2. Use Silicone To Hold The Plywood In Place
Next, you are going to begin to seal the plywood that you cut out.
You will want to make sure the strip of plywood does not slip when it is installed in front of the dishwasher.
It needs to be a perfect and seamless fit.
This is why you will want to use silicone to get the job done.
Apply the silicone evenly and ensure you press down the plywood until it holds. This is now the foundation for your fix.
3. Install Flat Wood Molding Into The Gap
Now, you are going to want to complete the finishing to get the look you desire.
This is where flat wood molding is going to come in handy.
You are going to do the same thing as you did with the plywood. Make sure to measure everything and set up the molding from one end to the other in the gap.
When done right, you will notice how it will create a seamless finish that is ideal for the space in front of the dishwasher.

4. Use Silicone To Seal The Molding
The last step is to seal the molding into place.
You are once again going to use the silicone you utilized beforehand. The goal here is to make sure the molding does not slip out of place or begin to crack.
Just make sure you apply the silicone evenly and wait until the molding is secure.
This is how you are going to get the results you are after.
Be thorough while doing this and make sure to take your time during the process. If you do this, you will appreciate how it all comes together and the quality you enjoy from the fix.
Final Thoughts
These are the tips that matter when it comes to getting a solution that works for the gap between a dishwasher and the floor.
If there is a gap between the dishwasher and the floor, start by installing a strip of plywood into the gap using silicone. Press and hold the strip until it locks into place. Next, use flat wood molding for the finishing and glue this into place using silicone too.
At this point, the gap will be gone and you are going to have a good semi-permanent solution that can be removed if you need to in the future.
For most people, these are the details that matter.
You will want to be diligent with what you are doing and make sure you are paying attention to your approach.
Look into these steps and know the gap will be taken care of once you are done.
Read More On Kitchens:
- How To Make Dishwasher Taller
- How To Remove Dishwasher Stuck Due To The Flooring
- Main Causes For Samsung Dishwasher’s Pump Always Running
- Why Is The Samsung Dishwasher Refusing To Rinse Before Draining?
- Why Is The Frigidaire Dishwasher Not Moving Past The Wash Cycle?
- Why Is My Dishwasher Coming With Two Wires?