Most people will go through a full wash cycle when it is time to use their dishwasher.
However, what if you have already rinsed the dishes?
Is there an option where you can run the Whirlpool dishwasher heat dry only?
Yes, you can run the Whirlpool dishwasher heat dry only if needed. Simply load the dishes, maintain a smaller load, and set the Heat Dry setting.
The only time this is a concern is when you overload the dishwasher. This is not good for the drying process and might make it harder to get the type of finish you’re after.
In a situation such as this, the best option is to go with a trial-and-error process. This means you see how the Whirlpool dishwasher does based on the number of dishes you put in it.
For the most part, it is recommended to not overload the dishwasher with plastic. This type of material is much harder to dry compared to others.
This article will look at a few tips on how to run the Whirlpool dishwasher Heat Dry only.
Table of Contents
Best Sponge For Dishes (EDITOR’S CHOICE)
No products found.
Tips To Run Whirlpool Dishwasher Heat Dry Only
1. Avoid Putting Too Much Plastic Inside
This is the most common mistake that’s made.
While there is nothing wrong with putting plastic in a Whirlpool dishwasher, it is going to put too much stress on the machine.
This is not good for the dishwasher and it will cause it to leave the plastic wet.
It is better to make sure you are not putting too much plastic inside as it will cause it to remain wet.
Instead, if you are going to put plastic inside, you will want to put only a few items. This will allow the dishwasher to take care of the dishes and everything else in the appliance.
It is important to take your time placing the dishes into the appliance.
Otherwise, you are going to create a situation where the dishwasher might not do a good job.

2. Always Run A Smaller Load
Along with the type of dishes you are putting in the Whirlpool dishwasher, it’s also important to think about the type of load you are running.
You will want to look to run a smaller load.
This is going to help reduce the amount of power needed by the dishwasher to dry the dishes. Take your time loading the dishes and make sure they are spread out a bit.
This will go a long way in making it easier for the dishwasher to do what it needs to do.
3. Check The Timer
You will want to take the time to check the timer.
A lot of people don’t check the timer and this is a major concern for those who want to do things properly.
You will want to see how long it’s going to take for the Heat Dry setting to take hold. This is usually going to take an hour to get the job done.
If the timer is off, you will want to reduce some of the load in the appliance.
This is going to help increase the chances of the dishwasher working the way it is supposed to.
Don’t underestimate how important this is when looking to do things the right way.

4. Inspect The Dishes
You will want to now take the dishes out after they have gone through the heat cycle.
This should take an hour or so.
Once you are done, you are going to look at various dishes from the racks to see whether or not they dried as intended.
For the most part, this should have worked and your dishes should be good to go.
After you have a good feel for what works and what does not, you can begin to speed up the process.
Final Thoughts
Can you run Whirlpool dishwasher heat dry only?
You can run the Whirlpool dishwasher heat dry only to heat the dishes. This is common after rinsing them in the sink. To do this the right way, avoid putting too many plastics in the same load, reduce the number of dishes in the load, and then let the heat setting run.
This will do a good job of making sure the dishes dry as soon as they need to.
If you are doing this for the first time, you will want to start with a smaller load. This is a test run and it should allow you to get a feel for how long it takes and what the process entails.
As time goes on, you can start to make adjustments as needed.
Read More On Kitchens: