If the Delta faucet handle is stuck, you will attempt to pull it off with force. This is a common approach to removing the average handle but it likely won’t work.
Instead, you are going to have to figure out how to remove a Delta faucet handle if it won’t come off easily.
To remove a Delta faucet handle if it won’t come off, drill into the Allen keyhole on the side. This will loosen the faucet handle. Now, take a woodblock, press it against the Allen keyhole, and hit it gently using a hammer. This will further loosen the handle allowing you to wedge something sharp into the base before pulling it up.
One of the main reasons a Delta faucet handle gets stuck has to do with calcium deposits. These harden the handle and make it difficult to budge from its spot.
Here is a look at what you have to do if the Delta faucet handle won’t come off easily.
Best Delta Faucet (EDITOR’S CHOICE)
No products found.
Steps On How To Remove Delta Faucet Handle If It Won’t Come Off
1. Drill Through The Allen Keyhole On The Side
If you want to remove a Delta faucet handle with no visible screws, it’s important to look at the Allen keyhole.
Why is this hole important?
It’s going to allow you to gain access to the holding component that is keeping the Delta faucet handle in place. Each model has an Allen key hole such as this that is accessible from the side. You should see it when you inspect the handle.
Once you find this handle, you are going to take a drill and loosen it. You don’t have to drill with force while doing this.
Just gently turning on the drill and spinning it with the right bit is going to get the job done. Make sure it is the right fit when you are going through the drilling process.
2. Press Woodblock Against The Side
You are now going to take a woodblock and press it against the side.
Your goal here is to make sure the woodblock is flush against the side of the handle. If you do this, it is going to ensure any hit to the side of the woodblock is going to cause the handle to loosen.
Why not hit it directly without the woodblock?
You will want to protect the surface of the Delta faucet handle. Directly hitting it with a hammer is going to cause it to break or crack!
This is why it’s important to be careful during the hammering process. The woodblock can help with this part of the process.
3. Hit Gently With Hammer
You won’t need a Delta faucet handle removal tool for this process.
Instead, you are going to have the woodblock pressed against the hole and then hit it with a hammer. When you are doing this, don’t start swinging the hammer aggressively.
This will cause the handle to fracture and that is going to render it useless.
The goal is to hit it lightly and then see if it budges. For the most part, you are going to notice it will budge with a few taps.
This is key as you figure out how to remove a Delta faucet handle that is stuck.

4. Wedge The Screwdriver Into The Base And Pull Up
The last step is to pull it out.
To do this, you are going to take a screwdriver and press it deep into the base of the Delta faucet handle. This will become noticeable as soon as you hammer the side of the faucet.
It will begin to loosen.
This will create a gap near the base that you can wedge the screwdriver into. It does not have to be a screwdriver but this is an easy tool to manipulate as you begin pulling up.
The last step is to keep pulling until it comes off. It should not require a lot of force to do this.
Final Thoughts
These are the steps to follow if a Delta faucet handle won’t come off.
To remove a Delta faucet handle that won’t come off, start by drilling into the Allen keyhole. Now, grab a woodblock and press it against the side of the hole. Begin hammering the woodblock gently in a bid to get the handle to loosen. With a few hits, it will loosen. Now, wedge a screwdriver into the gap near the base and pull up. The handle should come off.
This is all you are going to have to do if the Delta faucet handle is stuck.
Read More On Faucets: