The control panel is a critical part of modern Whirlpool fridges.
This is why most people’s eyes go towards it once they’re paying attention to the fridge. Keeping this in mind, it is important to know what to do when the whirlpool refrigerator control panel is flashing.
If the whirlpool refrigerator control panel is flashing, the wires and/or connectors are likely loose. These are located underneath the hinge cover. Check the wires to make sure they are firmly in place. If this does not work, consider a refrigerator control panel reset by unplugging the fridge for a few hours.
Most of the issues tend to involve the electrical components associated with the fridge. If they are loose or damaged, the control panel is going to begin flashing.
This article will showcase how to fix a Whirlpool refrigerator control panel that is flashing. Learn what is required to repair the flickering Whirlpool refrigerator control panel and what not to do during the process.
Table of Contents
Best Fridge Alarm (EDITOR’S CHOICE)
No products found.
How To Fix Whirlpool Refrigerator Control Panel That’s Flashing
1. Remove The Hinge Cover
If the Whirlpool fridge control panel is blinking, you will have to check the wiring.
This is often noted as being the number one reason for the control panel to not work. By removing the hinge cover, you are going to gain access to the wiring running into the control panel.
It will have 1-2 screws that are going to hold the hinge cover in place.
Get a screwdriver and begin to remove the screws. Remember, you will need the screws later on. Place them in a safe spot.
It is important to note, some Whirlpool fridges have wiring running through the back of the fridge. If necessary, go through the manual to see where the wiring is located before opening things up.

2. Check for Loose Wires Or Connectors
If the Whirlpool refrigerator control panel is flickering, you will have to begin assessing the wires to see if they are firmly in place.
As soon as you have access to what’s underneath the hinge cover, you will begin to spot potential issues with the wiring.
This can include loose wires or connectors that need to be re-attached. Whatever the reason may be, you should make sure to push all of these components back into place properly. This will bode well for other issues too.
Be patient while doing this and make sure the wiring is not an issue later on.
3. Replace Damaged Wires (If Necessary)
You will now want to consider replacing damaged wires.
This is going to depend on your inspection and whether or not the replacement is necessary. In most cases, you will not have to do this.
The reason has to do with the control panel still having power going to it. If it is flickering or blinking, this means there is enough electrical power available to the control panel where it can continue to flash.
If the wire was completely damaged, it would not send power through to the control panel.
This is why it’s essential to replace all damaged wires carefully if you believe this is an important step in the process.
If not, you will want to move on to the next step.

4. Unplug the Fridge For 2-3 Hours
This is going to be the final option before the control panel has to be replaced.
In general, you will want to consider a Whirlpool refrigerator control panel reset.
This is easy to do and is not going to take a lot of time. The idea is to unplug the Whirlpool fridge and make sure no power is going through to it. You will want to do this for approximately 2-3 hours and then plug it in again.
The goal here is to reset the Whirlpool refrigerator control panel and make sure it is back to how it was before the problem occurred.
Final Thoughts
These are the details to think about when the Whirlpool fridge control panel is flashing.
When a Whirlpool fridge control panel is flashing, it’s often going to involve the wires or connectors being loose. To correct this issue, you will want to remove the hinge cover to expose the wires. This will let you test whether or not the wires are loose. Push all of the wires into place to fix the problem. If the fridge still doesn’t work, unplug it for 2-3 hours. This will reset the control panel.
Take your time with the process and be as patient as possible.
Read More On Kitchens:
- Causes of Whirlpool Dishwasher Leaking All The Time
- Can Fridge Be Used Without A Functional Water Line?
- Reasons Fridge Keeps Making Noise
- Why Is Fridge Running Constantly?
- What Is The Best Length of Time To Store Fridge Before Using It?
- Why Does Whirlpool Fridge Light Keep Flashing?
- How To Get Whirlpool Freezer Door Unstuck