How To Reset Merkury LED Strip (Explained)

Merkury LED strip lights are gorgeous and renowned for being one of the best options on the market in this category.

However, there are situations where the LED strip is not going to work as well as it should. You might end up dealing with a small error that has to be corrected for the Merkury LED strip lights to work again.

If that is the case, it is time to figure out how to reset the Merkury LED strip.

To reset the Merkury LED strip, press and hold 6 to get to Easy Mode. Now, wait for the LED light to blink two times in a second for the reset process to complete.

This process will take no more than a few seconds to complete.

If you are looking to manage the WiFi connection then it is best to reset the router too. This will depend on what is causing the LED strip to not work as it is supposed to. Go through each solution while troubleshooting the problem.

Here is a simple breakdown of what you have to do as you learn how to reset the Merkury LED strip.

Best LED Lights (EDITOR’S CHOICE)

No products found.

Steps On How To Reset Merkury LED Strip

1. Press And Hold “6”

If the Merkury LED strip is not turning on, you will want to initiate the reset process.

This starts by aiming to get to the “Easy Mode” setup through the app.

In general, this is going to be done by pressing and holding “6”, which will let you get to the mode you want to. This is key when troubleshooting a problem such as this where the LED strip is not working as required.

Do not rush this step and make sure you are holding it instead of just tapping it.

This will make sure it resets the way you want it to.

how to reset merkury led strip

2. Access “Easy Mode”

Now, you are going to get to the Easy Mode.

This is key as that is how you are going to let the strip know it is time to reset. Since there is high-tech detailing done when it comes to the strip’s engineering, they have made sure it is easy to reset.

This is going to take a few seconds once you are in Easy Mode.

3. Wait For The LED Light To Flash Two Times

This is the most important step in the process and one you are going to have to be aware of as soon as the process begins.

Remember, this process is only going to take a few seconds to complete.

At this stage, you are going to be in Easy Mode and you are still going to be holding “6” to complete the reset. If you let it go, you will have to start all over again.

Assuming you are still holding it, you are going to notice the LED strip light flash. It is going to have to flash twice in a second for the reset to initiate.

As soon as this happens, you can let go.

It will go through the rest of the process on its own and your strip should be back to how it was.

how to reset merkury led strip

4. Repeat (If Necessary)

Let’s assume something goes wrong and it does not flash or reset.

What are you going to have to do next?

You will want to go through the same steps again and it should work out as planned. In some cases, you will notice the light flash three times slowly.

If this happens, it means you have already reset the strip once and it is going to do it again. There is nothing wrong with this and it will be the same as resetting the Merkury strip the first time around.

Continue to keep an eye on the Merkury strip while this is happening. For the most part, it should be back to normal as soon as the resetting is done.

Final Thoughts

This is how to reset the Merkury LED strip the right way.

To reset the Merkury LED strip, start by pressing and holding “6” for a few seconds until you get to the Easy Mode. Once in this mode, continue holding “6” and wait until the LED strip flashes twice in a second. This means the reset has been initiated.

It is as simple as this.

The rest of the work is going to be done by the strip and it will go through the remaining steps quickly.

Within a few seconds, the LED strip will be back to how you want it to be. Remember, do not rush this process, and make sure you are following each step carefully.

Read More About Lights:

  1. How To Repair LED Strip Lights That Are Half Working
  2. Why Is My LED Bulb Not Working In Socket?
  3. Are LED Lights Usable In Bathrooms?
  4. Does LED Light Sync With A Dimmer?
  5. Are Bathroom Lights GFCI Friendly?