When the bathtub jets are used all the time, it’s common for issues to arise.
This is when you are going to want to know what the right measures are to get on top of things before the bathtub jets stop working for good.
This includes learning how to clean tub jets that don’t work.
To clean tub jets that don’t work, fill the tub with hot water, pour three scoops of dishwasher detergent, let the jets cycle a few times, and then drain the tub. The jets will now begin working.
It’s common for the bathtub jets to develop debris that settles on the surface. This causes the jets to stop functioning as they used to.
Do not worry when this happens as a few adjustments will go a long way in optimizing your setup.
This article is going to look at how to clean tub jets that don’t work without compromising on performance or safety.
Best Cleaner For Bathtub Jets (EDITOR’S CHOICE)
No products found.
Steps On How To Clean Tub Jets That Don’t Work
1. Fill Tub With Hot Water
The first thing you are going to want to do before cleaning the bathtub jets is to fill the tub.
The goal here is to make sure there is enough water in the tub for the jets to work. This will often involve filling the water up to the point where the jets are aligned in the bathtub.
Please note that you should make sure the water is hot.
This is going to help with the handling of detergent that is used later. You do not want to rush this process but taking care of this will go a long way in getting appropriate results.
When you have filled the bathtub, it is time to begin working on using the right cleaner.
2. Pour Three Cups Of Dishwasher Detergent
To clean bathtub jets that don’t work, you will need to use dishwasher detergent.
You can use any type of dishwasher detergent and the brand will not matter. It is recommended to go with a powdered solution as it will spread better and help with the cleaning of the jets.
As soon as you have the dishwasher detergent ready to go, you are going to pour three cups of it into the bathtub.
It is best to pour each cup into a different section of the bathtub.
This will make sure it spreads evenly and allows the cleaner to do what it is designed to do.
Take the time to mix it with your hands for a few seconds too.
3. Let The Jets Cycle A Few Times
Now that the dishwasher detergent is in the bathtub, you are going to turn on the bathtub jets.
This is going to begin the cycle.
You will want to make sure the bathtub jets are working at the right speed and you can let them cycle through a few times.
The purpose is to get the water moving as that is how you will flush out debris in the bathtub jets.
It is common for this process to take a few minutes and that will be enough to get the type of results that you are after.
4. Drain The Tub
You will want to make sure the drain the tub during the process.
The goal here is to ensure you don’t have hot water in the tub when the jets have been cleaned.
For the most part, a few cycles through the bathtub jets will be more than enough to clean them as you want to.
Be thorough and ensure you have let the process unfold as you desire.
When you are happy with the cleaning that has taken place, it is time to begin working on draining the bathtub.
Test the bathtub jets again and they should be working the way you want.
This is the best set of steps to look at as you figure out how to clean tub jets that don’t work.
To clean tub jets that don’t work, you will want to fill the tub with hot water. Next, pour three cups of dishwasher detergent in, let the jets run through a few cycles, and then drain the bathtub to complete the process.
At this stage, the bathtub jets should be completely clean and will begin to work as they are designed to.
If this does not work, you are welcome to repeat the process until you are satisfied.
This is the best way to make sure the bathtub jets are working again and will continue to deliver the results that you are hoping for.
Always be thorough when it comes to this type of process as that is how you are going to appreciate the results.
Read More On Bathrooms: